Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Before
After
Before
After
Before
AfterTrusted Garage Door Installation for Frisco Homeowners
A Frisco Garage Door Installation typically costs between $700 and $2,200, depending on door size, material, and whether you’re replacing an existing door or framing a new opening. We’ve been installing garage doors across Frisco since 2015, and every job starts the same way: a written price and scope before any work begins, per Clause 1 of The Haven Standard. That’s not a slogan. It’s how we’ve operated since Marcus Deller started Servo Garage Doors, and it’s why more than 18,000 homeowners have their garage doors made right by us. Call (940) 290-8313 for a free estimate, and you’ll get a line-item price on paper before you commit to anything.
We don’t ask you to trust us. We show you the documentation.
What Our Garage Door Installation Service Includes
Garage door installation means more than hauling away your old door and bolting up a new one. It means measuring the rough opening, checking the header and track mounting points, setting the spring tension correctly, and verifying the door balances across its full travel. Our crews handle every step, and at the end of the visit you receive a documented photo record of what was found, what was installed, and how it was finished. That record traces back to the founding rule Servo was built on: you see the condition of the work before anyone asks you to pay for it.
New Door Installation
New Door Installation replaces an existing door that’s past repair, or installs a door into an opening that previously had none. This is the right call when your current door has structural rust, a cracked section, or alignment problems that would cost more to patch than to replace. Servo Garage Doors Frisco handles full tear-out, disposal of the old door, track and hardware replacement, and final balancing so the door opens with even tension and closes without slamming.
Single Car Door
A Single Car Door is typically 8 to 9 feet wide and suits one-car garages or detached workshop bays. It’s the most common installation we perform in Frisco’s older neighborhoods, where garage footprints run narrower than newer builds. We install single car doors in steel, wood, and composite, and we carry track hardware rated for the door weight so the opener doesn’t fight the spring on every cycle.
Double Car Door
Double car doors run 16 to 18 feet wide and require a heavier torsion spring assembly and wider header reinforcement to carry the extra weight. We see a lot of these in Frisco’s newer subdivisions, where two-car garages are standard. Our installers size the spring to the exact door weight, not a chart guess, and we photograph the spring and cable setup before the first test cycle.
Custom Garage Door
Custom garage doors are built to nonstandard dimensions, unusual materials, or specific architectural styles that off-the-shelf doors won’t match. If your garage opening isn’t a standard size, or you want a specific wood species, glass configuration, or carriage-house profile, a custom door is the answer. Servo Garage Doors Frisco sources from manufacturers including Clopay and Amarr, and we quote custom work the same way we quote everything else: a flat, written price with the dimensions and materials spelled out before you sign anything.
Steel Doors
Steel garage doors are the most common choice for Frisco homes because they hold up to hail, heat, and the humidity swings we get in late spring. They come in insulated and non-insulated versions, usually with a baked-on finish that resists fading. We install steel doors in single and double widths, and we recommend insulation ratings based on whether your garage is attached to your living space or stands alone.
Wood Doors
Wood garage doors offer a look that steel can’t match, but they require more maintenance and a heavier frame to carry the load. We handle installation of Clopay and custom wood doors, including cedar and hemlock, with the proper sealing and hardware to handle North Texas heat without warping. Wood doors weigh more than steel, so spring sizing and track reinforcement matter more here than anywhere else; we document both at installation.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Garage Door Installation
We install and service LiftMaster and Chamberlain openers alongside the doors we hang, and we stock their OEM parts on our trucks. That matters because a new door paired with an underpowered or misaligned opener will fail early, and we’d rather set both up correctly the first time than come back and explain why the logic board burned out. When you buy a LiftMaster opener with your door installation, we program the travel limits and force settings so the opener isn’t working harder than the spring.
Clopay is our most-installed door brand, and we’ve put in hundreds of their steel and wood models across Frisco, Prosper, and The Colony. We also work with Genie openers on existing setups, including older units that need a trolley carriage or limit switch adjustment to work smoothly with a new door. Whether you have Clopay, LiftMaster, Chamberlain, Genie, or any other make, we can install it, wire it, and document it.
BeforeAfterSigns You Need Garage Door Installation Right Now
- Cracked or separated door sections. A horizontal crack across a panel isn’t just cosmetic. Water gets in, the section loses rigidity, and the door starts binding in the tracks. In Frisco, where we go from dry heat to sudden downpours, a cracked panel usually means the door is on borrowed time.
- Rust at the bottom rail or hinge points. Surface rust is manageable. Rust that has eaten through the metal at the bottom rail or the hinge fasteners compromises the door’s structure. Once the hinge screws can’t hold, the door sags and the rollers chew up the track.
- The door won’t balance, even after spring adjustment. If a technician has already set the spring tension and the door still feels heavy or drops when released mid-travel, the door itself may be too far out of spec to save. A door that can’t balance is a door that’s damaging the opener, the cables, and the tracks every time it cycles.
- Energy bills climbing and the garage is attached. An uninsulated or poorly sealed door against a conditioned living space leaks heat in summer and cold in winter. Frisco summers push attic and garage temperatures past 120 degrees. An insulated steel door with proper weatherstripping is often the single biggest improvement you can make to an attached garage.
- The door is dented badly enough to affect operation. Hail damage is common in Collin County, and while small dents don’t matter, a dent that’s creased the panel or knocked a track out of alignment does. If you’re fighting the door to open or close, installation of a new door may be cheaper than repeated repairs.
Our Garage Door Installation Process - Step by Step
- 1
Measure and document. We measure the rough opening, check the header for level, inspect the existing track and mounting hardware, and photograph everything. This is Clause 4 in action: the condition gets documented before anyone quotes a replacement.
- 2
Written scope and flat price. You receive a written estimate with the door model, dimensions, material, insulation rating, spring type, and the total installed price. No ranges, no “we’ll see once we get in there.” The price on the page is the price you pay.
- 3
Removal and prep. We remove the old door and hardware, dispose of it, and address the mounting surfaces. If the header needs reinforcement or the track brackets need new anchors, we handle that before the new door goes up.
- 4
Installation and tuning. We hang the door, set the tracks, wind the torsion spring to the manufacturer’s spec for your door’s exact weight, and test the full travel. If an opener is involved, we program the limits and force settings and verify the safety reversal works.
- 5
Documented photo record. Before we leave, you get photos of the installed hardware, the spring and cable setup, the opener configuration, and the finished door. The warranty paperwork is included in the same record. You see exactly what was done.
How Much Does Garage Door Installation Cost in Frisco?
New door installation in Frisco runs $700 to $2,200 for most residential doors-see our Garage Door Installation cost guide below for full details. A basic single car steel door with no insulation typically lands in the $700 to $1,100 range installed. A double car steel door with insulation usually runs $1,200 to $1,800. Custom wood doors start higher, often $1,800 to $2,200 or more depending on species and hardware. These are installed prices, including removal of the old door and standard track and spring hardware.
| Service | Price Range in Frisco |
|---|---|
| New Door Installation | $700 – $2,200 |
| Single Car Door (steel, basic) | $700 – $1,100 |
| Double Car Door (steel, insulated) | $1,200 – $1,800 |
| Custom Wood Door | $1,800 – $2,200+ |
| Opener Installation (if added) | $250 – $550 |
What moves the price: door width, material, insulation rating, window inserts, and whether the existing track and springs can be reused. What shouldn’t move it: the price you were given. When we quote a job, the scope is written and the price is flat. If the scope changes, we write a new scope and a new price before we touch anything. That’s Clause 1 of The Haven Standard, and it’s the reason we can publish our price ranges on this page instead of asking you to call for a quote.
To avoid overpaying, get the spring size, track gauge, and door weight in writing. If another company gives you a written estimate, bring it in and we’ll give you a free second opinion on it. If our estimate is higher, you’ll see why on the line items. If it’s lower, you’ll see that too.
Garage Door Installation Near Frisco - Our Service Area
Servo Garage Doors Frisco installs garage doors throughout Collin and Denton counties, including Garage Door Installation in Prosper, Garage Door Installation in The Colony, Little Elm, Plano, Allen, McKinney, Celina, Lewisville, Far North Dallas, Carrollton, and Richardson. We schedule installation visits across the area, and emergency repair calls are answered by a live person 24/7. If you’re in Frisco or a neighboring city, we’ll confirm a written price before we send a technician.
For more on what we do, see our home page and our Garage Door Installation in Frisco service details.
Serving Frisco, TX - Our Local Coverage Area
We’re based in the Frisco area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Garage Door Installation in Frisco
Garage door installation is the process of measuring a garage opening, removing any existing door, and installing a new door with tracks, springs, cables, and hardware. It includes setting spring tension to the door’s weight and testing the full open and close cycle. At Servo, installation ends with a documented photo record of everything that was installed and adjusted.
A standard single or double door installation takes 3 to 5 hours, including removal and disposal of the old door. Custom doors or installations that require header reinforcement can take a full day. We’ll tell you the expected time window in your written scope before the work starts.
Most residential installations run $700 to $2,200 depending on door size, material, and insulation. A single car steel door starts around $700, while a double car insulated steel door is usually $1,200 to $1,800. Call (940) 290-8313 for an exact written quote, free.
Yes, we install and service LiftMaster and Chamberlain openers, and we carry their OEM parts on our trucks. We also work with Genie and other major brands. If you need an opener installed with your new door, we’ll include the opener price and programming in the same written scope.
No, installation is scheduled work. It requires measurements, door ordering, and a planned time window. If your door has failed and you need it closed or secured, emergency garage door repair is available 24/7 with a live person answering the call, not a recording. If a repair turns out to require replacement, we’ll give you a written installation price on the spot.
Every installation carries the 365-Day Done Right Promise: if it’s not done right, we make it right, backed by The Haven Standard, not a handshake. Door and opener warranties from the manufacturer are included in your documentation. Your photo record includes the warranty paperwork and the exact work performed.
Clear the area inside the garage about three feet back from the door, and move vehicles out of the driveway. If you have items stored near the track or opener, move them aside. We’ll handle the removal, disposal, and cleanup of the old door and hardware. The only thing you need to do before we arrive is confirm the written price, which we send before the work begins.
Schedule Your Garage Door Installation Service in Frisco Today
Call (940) 290-8313 and you’ll talk to a live person who can schedule your installation and confirm the written price before any work starts. Estimates are free, the price is flat, and the scope is in writing. No urgency, no handshake deals. Just a documented job done right, per The Haven Standard.
Written by Marcus Deller, Owner at Servo Garage Doors, serving Frisco since 2015.